Theoretical estimation of dielectric loss of oxide glasses using nonequilibrium molecular dynamics simulations

To theoretically explore amorphous materials with a sufficiently low dielectric loss, which are essential for next-generation communication devices, the applicability of a nonequilibrium molecular dynamics simulation employing an external alternating electric field was examined using alkaline silicate glass models. In this method, the dielectric loss is directly evaluated as the phase shift of the dipole moment from the applied electric field. This method enabled us to evaluate the dielectric loss in a wide frequency range from 1 GHz to 10 THz. It was observed that the dielectric loss reaches its maximum at a few THz. The simulation method was found to qualitatively reproduce the effects of alkaline content and alkaline type on the dielectric loss. Furthermore, it reasonably reproduced the effect of mixed alkalines on the dielectric loss, which was observed in our experiments on sodium and/or potassium silicate glasses. Alkaline mixing was thus found to reduce the dielectric loss.     

Powder sintering and gel casting methods in making glass foam using waste glass: A review on parameters,performance, and challenges

The application of insulation materials in buildings and energy storage facilities is gaining global attention to reduce energy consumption, heat loss, and CO₂ emissions. Given the high insulation performance, glass foam is gaining popularity replacing combustible, high energy-consuming, and costly conventional insulation materials. The industrial process of glass foam manufacturing is an energy-consuming and non-ecofriendly process which requires the annealing of glass around its melting temperature. Therefore, researchers have developed powder sintering and gel casting methods to sinter glass foam mix at a temperature slightly above its glass transition point. However, research findings on these two methods are scattered because of the different parameters being used by researchers. The properties and performances of glass foam depend on the processing parameters, especially on the materials design and sintering conditions. Therefore, this study aimed to provide a comprehensive review on the key parameters for material selection and sintering of glass foams and provide necessary guidelines for the best practice and a direction for future research. Moreover, this review covers the current strategies and challenges associated with the powder sintering and gel casting methods including their sustainability and environmental performance.     

Effects of alkali metal ion on imprinting GRIN microstructure in GeS2-Ga2S3-MCl (M=Na,K, Cs) glasses for visible to mid-infrared microgratings

Gradient refractive index (GRIN) micro-optics present unique opportunities for control of the chromatic properties, new degrees of freedom for optical design as well as the potential for use in new optical system applications. GRIN microgratings were imprinted in GeS₂-Ga₂S₃-MCl (M = Na, K, Cs) chalcohalide glasses by microthermal poling, and the effects of the type and concentration of alkali cations on their performance were investigated. Two effective imprinting formation regions of the GRIN microstructure based on the poling saturation voltage (U_s) and glass composition are observed at fixed poling time and temperature. The U_s increases from 140 to 750 and 2600 V in accordance with the activation energy (E_a) of alkali ions (Na⁺ to K⁺ and Cs⁺) increasing from 45.15 to 58.62 and 92.58 kJ/mol for studied samples. The saturated numbers of diffraction order (N_s) of the gratings in these samples are 7, 9 and 6, respectively, the highest number being provided by the K⁺-containing sample. This is in accordance with imprinting-induced phase differences (0.14λ, 0.19λ and 0.09λ) measured in the fabricated samples containing Na⁺, K⁺ and Cs⁺ ions. Furthermore, the U_s of samples decreases from 1500 to 300 V with four concentrations of K⁺ from 10 to 30%, associated with their E_a of K⁺ decreasing from 69.62 to 53.46 kJ/mol, while N_s increases from 8 to 14, which is attributed to the increase of the phase difference in the GRIN structures. The controllable GRIN microstructures are realized by adjusting the type and concentration of alkali cations in chalcohalide glasses, which is expected to drive the design of broadband GRIN microgratings.     

Photoluminescence and X-ray excited scintillating properties of Tb3+-doped borosilicate aluminate glass scintillators

lthough single crystal scintillators have excellent performance, they have some drawbacks such as high cost, complicated elaboration method and difficulty of growth on large-scale. Glass scintillators are widely investigated to replace single crystal scintillators because of their simple fabrication method and low cost. In this paper, a series of transparent borosilicate aluminate glass scintillators doped with Tb³⁺ were successfully prepared by traditional melt-quenching method. The structural, luminescent, and X-ray excited scintillating properties were investigated. These glass samples show high stability and high transparency, and present good luminescent and scintillating properties. Sample with Tb³⁺ doping concentration of 10% has the best scintillating performance. The integrated intensity of X-ray excited luminescence is 66.6% of that of commercial Bi₄Ge₃O₁₂ single crystal scintillator, and the quantum efficiency (under 378 nm excitation) is 70.3%. Our findings suggest that Tb³⁺-doped borosilicate aluminate glasses with high light yield might be used as potential scintillators.     

Nanograin–glass dual-phasic,elasto-flexible,fatigue-tolerant,and heat-insulating ceramic sponges at large scales

Ceramics are considered intrinsically brittle at room temperature, which is mainly attributed to the limited availability of crystallographic slips and pre-existing geometrical flaws. Moreover, the lack of flexibility has severely hindered many high-end applications of ceramic materials. Here, we produce ceramic sponges that are simultaneously ultra-light, elasto-flexible, thermally insulating, and can fully recover from large deformation with a near-zero Poisson's ratio. These spongy materials also possess superb fatigue resistance without the accumulation of damage or structural collapse for 10,000 large-scale compressive or buckling cycles. We demonstrate the exceptional flexibility is enabled by the elastic distortion of nanograin–glassy dual phase and the fiber bulking in open-cell three-dimensional structure. Moreover, these spongy materials possess superior temperature-invariant superelasticity from deep cryogenic temperatures (−196 °C) to high temperature (1500 °C). Our study not only developed mechanically reliable lightweight ceramics for numerous extreme applications, but also provided new theoretical insights into the origin of flexibility in polycrystalline ceramics.     

Investigation of the Ga-Sb-S chalcogenide glass with low thermo-optic coefficient as an acousto-optic material

In this study, two series of Ga_xSb_40-xS₆₀ (x = 4, 6, 8, 10 mol%) and Ga_ySb₃₆S_64-y (y = 3, 5, 6 mol%) glasses were prepared and the relationship between their compositional and acousto-optic (AO) properties was investigated systematically for the first time. In the Ga_ySb₃₆S_64-y system, the AO figure of merit (M₂) increased as the Ga increased, and the maximum M₂ of the Ga₆Sb₃₆S₅₈ glass was 455.78 × 10^?18 s³/g, which is ～301 times greater than that of fused silica and ～2.5 times greater than that of As₂S₃ chalcogenide (ChG) glass at 1550 nm. However, its thermo-optic coefficients (dn/dT) varied greatly (32.1 × 10^?6 °C^?1–57.2 × 10^?6 °C^?1), and acoustic attenuations (α) at 10 MHz were high, from 5.446 dB/cm to 7.274 dB/cm. In the Ga_xSb_40-xS₆₀ glass system, the M₂ value and α at different ultrasonic frequencies gradually decreased with the improvement of Ga. Compared with the Ga_ySb₃₆S_64-y system, the Ga_xSb_40-xS₆₀ glass system had lower α (at 10 MHz) and dn/dT, which are 5.001 dB/cm–5.563 dB/cm and 17.3 × 10^?6 °C^?1–55.6 × 10^?6 °C^?1, respectively. These results provide a significant reference for the further development of novel ChG glasses and help expand their application fields.     

Designing amorphous formulations of polyphenols with naringin by spray-drying for enhanced solubility and permeability

Naringin (NAR), a major flavanone (FVA) glycoside, is a component of food mainly obtained from grapefruit. We used NAR as a food additive to improve the solubility and permeability of hydrophobic polyphenols used as supplements in the food industry. The spray-dried particles (SDPs) of NAR alone show an amorphous state with a glass transition temperature (T_g) at 93.2 °C. SDPs of hydrophobic polyphenols, such as flavone (FVO), quercetin (QCT), naringenin (NRG), and resveratrol (RVT) were prepared by adding varying amounts of NAR. All SDPs of hydrophobic polyphenols with added NAR were in an amorphous state with a single T_g, but SDPs of hydrophobic polyphenols without added NAR showed diffraction peaks derived from each crystal. The SDPs with NAR could keep an amorphous state after storage at a high humidity condition for one month, except for SDPs of RVT/NAR. SDPs with NAR enhanced the solubility of hydrophobic polyphenols, especially NRG solubility, which was enhanced more than 9 times compared to NRG crystal. The enhanced solubility resulted in the increased membrane permeability of NRG. The antioxidant effect of the hydrophobic NRG was also enhanced by the synergetic effect of NAR. The findings demonstrated that NAR could be used as a food additive to enhance the solubility and membrane permeability of hydrophobic polyphenols.     

Mechanical properties,corrosion resistance,and rubber pad forming of cold differential speed-rolled pure titanium for bipolar plates of proton-exchange membrane fuel cells

Due to problems such as pores on surface-treated coatings, the corrosion resistance of pure titanium bipolar plates for proton-exchange membrane fuel cells can be further improved by increasing the corrosion resistance of pure titanium by using differential speed-rolling (DSR); however, these materials have not yet reached the standard requirements of bipolar plates (corrosion current density i_corr＜10³ nA·cm^?2). In this work, the corrosion resistance of pure titanium was improved by optimizing the DSR process while the strength was maintained. The best corrosion resistance of the DSR pure titanium was achieved when the roller speed ratio was 2, while i_corr was 429 nA·cm^?2 in a solution of 0.5 M H₂SO₄ and 2 mg/L HF at room temperature. The formability of the DSR pure titanium for bipolar plates was verified. The optimal holding pressure range was 6.8–7.0 kN.     

Stabilization of natural gas foams using different surfactants at high pressure and high temperature conditions

Natural gas foam can be used for mobility control and channel blocking during natural gas injection for enhanced oil recovery, in which stable foams need to be used at high reservoir temperature, high pressure and high water salinity conditions in field applications. In this study, the performance of methane (CH₄) foams stabilized by different types of surfactants was tested using a high pressure and high temperature foam meter for surfactant screening and selection, including anionic surfactant (sodium dodecyl sulfate), non-anionic surfactant (alkyl polyglycoside), zwitterionic surfactant (dodecyl dimethyl betaine) and cationic surfactant (dodecyl trimethyl ammonium chloride), and the results show that CH₄-SDS foam has much better performance than that of the other three surfactants. The influences of gas types (CH₄, N₂, and CO₂), surfactant concentration, temperature (up to 110°C), pressure (up to 12.0 MPa), and the presence of polymers as foam stabilizer on foam performance was also evaluated using SDS surfactant. The experimental results show that the stability of CH₄ foam is better than that of CO₂ foam, while N₂ foam is the most stable, and CO₂ foam has the largest foam volume, which can be attributed to the strong interactions between CO₂ molecules with H₂O. The foaming ability and foam stability increase with the increase of the SDS concentration up to 1.0 wt% (0.035 mol/L), but a further increase of the surfactant concentration has a negative effect. The high temperature can greatly reduce the stability of CH₄-SDS foam, while the foaming ability and foam stability can be significantly enhanced at high pressure. The addition of a small amount of polyacrylamide as a foam stabilizer can significantly increase the viscosity of the bulk solution and improve the foam stability, and the higher the molecular weight of the polymer, the higher viscosity of the foam liquid film, the better foam performance.     

Eco-friendly tape casting of borosilicate glass/Al2O3 sheets for LTCC applications

This work reports the innovative development of a borosilicate glass/Al₂O₃ tape for LTCC applications using an eco-friendly aqueous tape casting slurry. Polyvinylpyrrolidone (PVP) and polyacrylic acid (PAA) were the respective dispersants, while carboxymethyl cellulose (CMC) and styrene acrylic emulsion (SA) were the respective binders. The results showed that PVP was more suitable than PAA as the dispersant for the aqueous casting slurry, and that 1.5 wt% PVP would achieve well dispersion of CABS glass/Al₂O₃ powder in the aqueous slurry. Moreover, a small amount of 2.0 wt% CMC binder could yield smooth CABS glass/Al₂O₃ tapes crack free. A high-quality CABS glass/Al₂O₃ tape with a smooth surface was made from an aqueous slurry containing 1.5 wt% PVP dispersant, 2.0 wt% CMC binder, and 2.0 wt% PEG-400 plasticizer. The density, tensile strength, and surface roughness of the green tape were 2.05 g/cm³, 0.87 MPa, and 148 nm, respectively. The resulting CABS glass/Al₂O₃ composites sintered at 875 °C exhibited a bulk density of 3.14 g/cm³, a dielectric constant of 8.09, a dielectric loss of 1.0 × 10^?3, a flexural strength of 213 MPa, a thermal expansion coefficient of 5.30 ppm/^°C, and a thermal conductivity of 3.2 W m^?1 K^?1, thus demonstrating its broad prospects in LTCC applications.